作者： 深圳市叁鼎科技有限公司發表時間：2021-06-03 11:05:33瀏覽量：2886【小中大】
導通孔起線路互相連結導通的作用，電子行業的發展，同時也促進FPC線路板乃至fpc軟硬結合板的發展，也對印制板制作工藝和表面貼裝技術提出更高要求。FPC線路板塞孔工藝應運而生，同時應滿足下列要求：With the development of electronic industry, it also promotes the development of FPC circuit board and FPC hard and soft combination board. It also puts forward higher requirements for PCB manufacturing process and surface mount technology. The plug hole technology of FPC circuit board arises at the historic moment, which should meet the following requirements:
1. 導通孔內有銅即可，阻焊可塞可不塞; The copper in the through hole is enough, and the resistance welding can be plugged or not;
2. 導通孔內必須有錫鉛，有一定的厚度要求（4微米），不得有阻焊油墨入孔，造成孔內藏錫珠；There must be tin and lead in the through hole, with a certain thickness requirement (4 microns), no solder resist ink into the hole, causing tin beads in the hole;
3. 導通孔必須有阻焊油墨塞孔，不透光，不得有錫圈，錫珠以及平整等要求。
隨著電子產品向“輕、薄、短、小”方向發展，fpc多層軟硬結合板也向高密度、高難度發展，因此出現大量SMT、BGA的FPC線路板，而客戶在貼裝元器件時要求塞孔，主要有以下五個作用：The through hole must have solder resist ink plug hole, not transparent, no tin ring, tin bead and leveling requirements.
With the development of electronic products in the direction of "light, thin, short and small", FPC multi-layer soft and hard boards are also developing to high density and high difficulty. Therefore, a large number of FPC circuit boards with SMT and BGA appear. Customers require plug holes when mounting components, which mainly have the following five functions:
①. 防止FPC線路板過波峰焊時錫從導通孔貫穿元件面造成短路；特別是我們把過孔放在BGA焊盤上時，就必須先做塞孔，再鍍金處理，便于BGA的焊接。
To prevent short circuit caused by tin penetrating through the element surface from the through hole during wave soldering of FPC circuit board; In particular, when we put vias on BGA pads, we must first plug the vias and then gild them to facilitate BGA welding.
②. 避免助焊劑殘留在導通孔內；
Avoid flux remaining in the through hole;
③. 電子廠表面貼裝以及元件裝配完成后PCB在測試機上要吸真空形成負壓才完成：
After the surface mount and component assembly of the electronics factory, the PCB should be vacuumed on the testing machine to form a negative pressure
④. 防止表面錫膏流入孔內造成虛焊，影響貼裝；
prevent the solder paste from flowing into the hole to cause false soldering and affect the mounting;
⑤. 防止過波峰焊時錫珠彈出，造成短路。
prevent solder bead from popping out during over wave soldering, resulting in short circuit.
叁鼎. 深圳市寶安區福海街道
福園一路137號盛恒基工業園C棟
Email: sales@sunfpc.com
Tel: +755 23 000 466
掃一掃,關注我們
一站式電子解決方案供應商！
